Log In     My Account       Your cart is empty.     SKYPE

Currencies:
     English  French  


Home >>  RF Receivers / Controllers >>  Receiver Modules >>  12 Channels DC 9~12V Output Super Regeneration - RF Wireless Receiver Module With Decoder

Stay In Touch

12 Channels DC 9~12V Output Super Regeneration - RF Wireless Receiver Module With Decoder


Price: US $18.00

Add to Cart:    Write Review

  • Model: 0020286

Please Choose:










 Manual

Feature:

  • Model No.: 0020286
  • Type: Receiver module with decode for fixed code
  • Modulation Method: Amplitude modulation (ASK or OOK)
  • Working Voltage: DC 9~12V
  • Working Current: 5~8mA
  • RF Sensitivity: -103dBm
  • Coding Method: Learning fixed code
  • Decoding Outputs: DC 9~12V
  • Working Temperature: -20°C ~ +70°C
  • Size: 42x39x24mm
  • With 12 decoding outputs
  • Control Modes: Toggle, Momentary, Latched
  • Frequency: We can offer 315 MHz or 433.92 MHz, you can choose one.

Application:

  • The RF receiver modules are widely used for remote controls, remote control toys, anti-theft alarms, garage doors, roller shutter, road barrier, retractable doors and so on.

Notes:

  • It is best to use the antenna of 1/4 wavelength, for antenna has a great impact on receiving effect of the module; normally using 50Ω single core cable. For frequency 315MHz, the length of antenna is about 23cm; for 433MHz, it is about 17cm. The position of antenna also affects the receiving effect of the module. When installing the antenna should be extended as much as possible and be away from the shield and the place in high pressure and interference.
  • The receiving frequency, decoding mode and timing resister should be compatible with the transmitter.

Learning methods and steps for 3 control models:

  • Press and hold the button of receiver, then release the button when LED flashes once, it means the receiver is in the status of LEARNING.
  • Press any button of 1, 2, 4, 8 of remote control in 10 seconds, if LED flashes quickly and then off, it means LEARNING is successful. If LED flashes once after 10 seconds, it means LEARNING is failed and the receiver will quit the status of learning.
  • The receiver can learn several remote controls of different codes.

Setting different control modes (We have set the receiver as Toggle control mode before delivery. If you want to use other control modes, do as following operation):

  • Learning method of control mode Momentary: When the receiver in the status of LEARNING, press button 2 or 8 of the remote control.
    Control mode Momentary (Channel 1~12): Press and hold -> On; Release -> Off.
    Such as:
    Press button 1 and hold: D1 output; Release button 1: D1 no output
    Press button 2 and hold: D2 output; Release button 2: D2 no output
  • Learning method of control mode Latched: When the receiver is in the status of LEARNING, press button 1 of the remote control.
    Control mode Latched (Channel 1~12): Press -> On, other outputs Off; Press other button -> Off.
    Such as:
    Press button 1: D1 output; others no output
    Press button 2: D2 output; others no output
  • Learning method of control mode Toggle: When the receiver is in the status of LEARNING, press button 4 of the remote control.
    Control mode Toggle (Channel 1~12): Press -> On; Press again -> Off.
    Such as:
    Press button 1: D1 output; Press button 1 again: D1 no output
    Press button 2: D2 output; Press button 1 again: D2 no output
  • If you don’t want the receiver to work with the remote control, you can delete all codes of remote controls, which are stored in the receiver.
    Operation: Press the button of the receiver for about 3 seconds until the LED light flashes quickly, and then release the button, the LED light will flash slowly, it means all stored codes have been deleted successfully. At this time, remote control cannot control the receiver.

Introduction of pin (from left to right)

    PinsFunction
    D1~D12Data output
    VCCPositive power supply
    GNDNegative power supply

Ask A Question
* Required information

*
*
tnge
*