How to remote control compressor, blower and pump?

I am looking to convert a keyed rotary switch with a remote control switch. The switch has 4 positions, position 1 is all Off. Position 2 lower (turns on compressor) Position 3 Raise (turns on a blower) and Position 4 Drain (turns on a pump). These are turned on individually not all at the same time. The voltage required to power the remote control is AC220V. No current is required to power the devices. The relays are basically open or closed. I would like a 4 channel RF product so I have one channel spare. Can you assist me with what product suits this please. {S2CIJ`3}[WDS1E7JHMHG0N According to the descriptions from this customer, we recommend him 4 CH Relay output long range waterproof case wireless remote control kit 0020450 (S4PU-AC220-ANT3+1CB-4). Set the receiver S4PU-AC220-ANT3 with Latched mode, then connect compressor to relay 2 in the receiver, connect blower to relay 3 in the receiver, connect pump to relay 4 in the receiver. This remote control kit is composed of a 4-channel receiver and 4-button transmitter that can be used in agriculture automation, industry automation, and home automation. It can control products on land, water and air, especially in a long distance, such as business signs, motorboat, farm, pasture, offshore unmanned operation, field call, remote security alarm, unmanned aerial vehicle, etc. Connected the compressor to the relay 1 of the 4 CH receiver, connect the blower to relay 2 of the 4 CH receiver, connect the pump to the relay 3 of the 4 CH receiver. 1 There are some remarkable characteristics of this 4 CH Relay output long range waterproof case wireless remote control kit. Waterproof Function: The 4 channel receiver has waterproof connector and waterproof shell/case, so it can be installed outside. Working Distance: With external telescopic antenna, this remote control kit can have further working distance. The working distance of the kit can reach 2000m in an open ground. If you stretches the external telescopic antenna, it can have a further working range. Relay Output: The 4 CH receiver is relay output that can be used to operate both DC and AC equipments. The terminal is NO / NC (normally open / normally closed), which serves as a switch. That means you should also connect a separate power supply to it. Power Output: Each relay output can work at maximum current 30A. The maximum power of the device is 3000W/110V, 6000W/220V. So it also can be used in agriculture and industry automation, such as long range and high power remote control devices. Input control terminals: The receiver has four input control terminals, you can connect external devices, sensors, or manual switches to these terminals to control the outputs of receiver. Three Control Modes: The 4 channel receiver has toggle / momentary / latched working control modes. We use latched control for 4 positions keyed rotary switch. How to set working control mode? Set toggle control mode (Press -> On; Press again -> Off): Only connect Jumper-2 Set momentary control mode (Press and hold -> On; Release -> Off): Only connect Jumper-1 Set latched control mode (Press -> On, other relays Off; Press other button -> Off): Disconnect Jumper-1 and Jumper-2 ZEBFZYY8V6Y[]JE(IXS]1AD We use 3 lamps to instead the compressor, blower and pump. Now let’s change the keyed rotary switch to remote control switch. Material Preparation: Receiver: S4PU-AC220-ANT3 Transmitter: CB-4 3 Lamps A keyed Rotary Switch Some Lines M The Wring Diagram: Just as the following pictures. Connect 3 lamps and 4 positions keyed rotary switch to the 4 Ch receiver. The black wire of the 3 lamps is connected and connect the other black wire to terminal “-“. Connect the red wire of 3 lamps respectively to terminal “A” of relay 1, relay 2 and relay 3. Connect red wire and black wire of the plug respectively to “+” and “-“ of the power. Please note that the red wire used to control lamp1 (compressor) should be connected to terminal A of the relay 1, the red wire used to control lamp2 (blower) should be connected to terminal B of the relay 2, the red wire used to control lamp2 (pump) should be connected to terminal B of the relay 3. The red wire used to turn off the equipments should be connected to terminal B of the relay 3. W Operation: Press button A of the transmitter, the lamp 1 turns on. 1 Press button B of the transmitter, the lamp 1 turns off and the lamp 2 turns on. 2 Press button C of the transmitter, the lamp 2 turns off and the lamp 3 turns on. 3 Press button D of the transmitter, turn off all of the lamps. 4 Online shop: http:www.carymart.com

Long range remote control well pump

We are looking for a wireless remote switch for our well pump at our cabin and I am wondering if one of your products could fit our needs. So quickly, our cabin is situated about 3/4 km from our water well pump. It’s pretty hilly and has trees in the way too. There is electricity at the pump head and right now we have to manually flick a on/off switch at the pump which is filling up the cistern in the house. Right now there is a timer at the pump which we can set so we don’t flood the house if we forget to flick it off. Ideally we would like to have a floating system in the cistern that would tell the pump to turn on/off wirelessly and when low/full or just having start for a small amount of time when low. I added a picture to the email to give you a better idea. Let me know if it’s something you can help us with.

QQ图片20151112110512

According to the description and picture from this customer, we recommend him to choose model: 0020525. It is an automatic water pumping system.

1_01-copy

There are some remarkable characteristics of this new product. We add external extend antenna which makes the transmitting distance of this system as long as 3000m. There are two operation methods of this remote controller. The first method is to control water pump motor with manual controller. The second method is to control water pump motor automatically by two mini water level sensors.

The manual operation is fairly easy. When pressing the big button of the transmitter, CB-2, the “ON” signal will be sent to the receiver. The receiver will instruct water pump motor to pump water into the tank. When pressing the small button of the transmitter, CB-2, the “OFF” signal will be sent to the receiver. The receiver will instruct water pump motor to stop pumping water.

Pumping water automation by water level sensors is the highlight of this product. The key technology is the transmitter, CB-2N-2, which is designed to have 3 external wires. We named them wire 1, wire 2 and wire 3. The three wires will be connected to two mini water level sensors.

Let’s show you how it works.

First step, it is installation.

Put the water level sensor 1 downwards and install at the low water level position; Put the water level sensor 2 upwards and install at the high water level position.

picture-1

Two wires of the water level sensor 1 are connected to wire 1 and wire 3 of transmitter CB-2N-2.

Two wires of the water level sensor 2 are connected to wire 2 and wire 3 of transmitter CB-2N-2.

pumping-water-device-1

Motor should be connected to A&B terminal and L&N terminal of receiver S1PUA-AC220-ANT2.

receiver-1

Second step:

When water reaches the low water level, two wires of the water level sensor 1 is connected and the transmitter is triggered. The transmitter will send an ‘ON”’ signal to the receiver. The receiver will instruct the water pump motor to pump water into the tank.

picture-2

picture-3

When water reaches the high water level, two wires of the water level sensor 2 is connected and the transmitter is triggered. The transmitter will send an “OFF” signal to the receiver. The receiver will instruct the water pump motor to stop pumping water.

picture-4

Online shop: www.carymart.com

 

Bad Behavior has blocked 45 access attempts in the last 7 days.