Log In     My Account       Your cart is empty.     SKYPE

Currencies:
     English  French  


Home >>  1000M-2000M Long Range Remote Control Kits >>  1 Channel AC & DC >>  Normally Open Heavy Duty DC 6V 9V 12V 24V RF Remote Controller Apply for Device Control Another Device 1CH 2000M

Stay In Touch

Normally Open Heavy Duty DC 6V 9V 12V 24V RF Remote Controller Apply for Device Control Another Device 1CH 2000M


Price: Starting at: US $80.00

Add to Cart:    Write Review

  • Model: 0020524 (S1PU-DC06/09/12/24V-ANT3 & CB-2N)

Please Choose:





















Feature:
Application: It can be used in industry automation, agriculture automation and home automation, such as factory, house, farm, pasture, vehicle, ship, offshore operation, aerial vehicle, field call, etc. It can remote control equipments on land, water and air, such as remote control lights, sirens, locks, motors, fans, winches, blinds, linear actuators, doors, windows, electric solenoid valves, security alarm, business signs and various devices.
Wireless control, easy to install.
Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.
Relay Output: This receiver is relay output, it can be used to operate both DC and AC equipments. The terminal is NO / NC (normally open / normally closed), which serves as a switch. That means you should also connect a separate power supply to it.
High Power: Each channel can work at maximum current 30A, such as 360W/12V, 180W/6V, 270W/9V, 720W/24V, 3000W/110V, 6000W/220V.
With wired control terminals: You can connect sensors, limit switches, manual switches or external devices to control the receiver.
With the external antenna, it can have a further working range.
Design with low-power and high-speed CMOS technology.
You can turn on/ off the receiver with transmitter (remote control) from any place within a reliable distance.
Wireless RF signal can pass through walls, floors, doors or windows.
With reverse power protection and over current protection.
Reliable control: The receiver only works with the transmitter which use same code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.
 
Receiver Parameters:
Model No. S1PU-DC06 –ANT3/ S1PU-DC09-ANT3 / S1PU-DC12-ANT3 / S1PU-DC24-ANT3
Power Supply (Operating Voltage): DC6V (S1PU-DC06-ANT3), DC9V±1V (S1PU-DC09-ANT3), DC12V±1V (S1PU-DC12-ANT3), DC24V±1V (S1PU-DC24-ANT3)
Output: Relay output (Normally open and normally closed)
Working Voltage Range of Relay: AC110~240V or DC0~28V
Working Frequency: 315MHz
Channel: 1CH
Control Modes: Latched
Static Current: ≤6mA
Maximum Working Current: 30A / each channel
PCB size: 90mm x 59mm x 18mm
Case size: 100mm x68mm x 50mm
Work with Fixed code transmitters or Learning code transmitters.
 
Matching Transmitters:
The receiver can work with different transmitters, such as model C-1 / C-2 (100M), CWB-1 / CWB-2 (50M, waterproof), CP-1 / CP-2 (500M), or CB-1 / CB-2 (1000M) etc.
When you set the receiver in toggle or momentary mode, it should work with single button transmitter, such as model C-1 (100M), CWB-1 (50M, waterproof), CP-1 (500M), or CB-1 (1000M) etc. When you set the receiver in latched mode, it should work with two buttons transmitter, such as model C-2 (100M), CWB-2 (50M, waterproof), CP-2 (500M), CV-2 (500M), or CB-2 (1000M) etc.
 
Working Range:
Super long range, with a transmitter (such asCB-2) to form a complete set, the maximum working distance can reach 2000M in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.
 
External telescopic antenna:
Length of external telescopic antenna: 108mm / 445mm (stretch)
External telescopic antenna use SMA connector.
If you stretches the external telescopic antenna, it can have a further working range, which is twice as much as it used to be.
Weight of external telescopic antenna: 16.5g
 
Usage (with the transmitter like C-2):
The receiver can be used to control both DC 0~28V and AC 110~240V equipments.
Notice: The receiver is relay output, not DC/AC power output. Initial state of relay output terminals: Terminals B and C are Normally Open; Terminals A and C are Normally Closed.
 
Wiring:
If you want to control a DC 12V lamp, do as following:
1) Connect the positive pole of DC power supply to terminal “L / +”, and connect the negative pole of DC power supply to terminal “N / -”.
2) Connect terminal B to the positive pole of DC power supply, connect terminal C to the positive pole of DC lamp, and connect the negative pole of DC lamp to the negative pole of DC power supply.
 
If you want to control an AC 220V lamp, do as following:
1) Connect the positive pole of DC power supply to terminal “L / +”, and connect the negative pole of DC power supply to terminal “N / -”.
2) Connect terminal B to the live wire of AC power supply, connect terminal C to one side of AC lamp, and connect another side of AC lamp to the neutral wire of AC power supply.
 
Setting different control modes
Setting different control modes (We have set the receiver as Toggle control mode before delivery. If you want to use other control modes, do as following operation):
 
Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.
Control mode Latched: Press -> On, other relays Off; Press another button -> Off.
Press button 1: Turn on the relay (connect B and C, disconnect A and C)
Press button 2: Turn off the relay (disconnect B and C, connect A and C)
 
Wired control terminals:
The receiver has manual control terminals, you can connect external devices, sensors, or manual switches to control the receiver.
1) Signal input:
You can connect external devices (with low level output signal) to manual terminals 1 (Signal -) and terminal 2 (Signal +), then the external device’s output signal can control the receiver.
When the external device outputs low level signal to manual terminal 1 and terminal 2, the receiver turns on the relay. (connect B and C, disconnect A and C)
When the external device stops to output signal, the receiver turns off the relay. (disconnect B and C, connect A and C).
 
2) The manual switches:
You can connect manual switch to terminals 1 and 2, and then you can use this manual switch to control the receiver.
When connect terminals 1 and 2, the receiver turns on the relay. (connect B and C, disconnect A and C).
And when disconnect terminals 1 and 2, the receiver turns off the relay. (disconnect B and C, connect A and C).
 
How to pair the transmitter to the receiver:
1) Press the learning button of receiver for 1- 2 seconds; signal LED on the receiver is on. The receiver enters into status of LEARNING.
2) Press any one button on transmitter. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.
4) The receiver can learn several remote controls with different codes.
 
Delete all transmitters:
We have learned remote control to the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of remote controls, which are stored in the receiver.
Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored codes have been deleted successfully.

Product Description:
Model No.: 0021045 (CB-2N)
With Extended Control Wires
Triggering method: connection and disconnection of two wires.
Shell Color: Grey
Channel/Button: 2
Button Symbol: big button, small button
Operating Voltage: 9V (1 x 6F22 -9V battery, can be used for a week, if you want a longer working time, please use a 9V power adapter.)
Operating Current: 10mA
Operating Frequency: 315Mhz / 433Mhz
Encoding Chip: PT2262 / PT2264 / SC2262
Encoding Type: Fixed code by soldering, up to 6561 codes
Transmitting Distance: 1000m / 3000ft (theoretically)
The distance of 1000m is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be exposed to some interference by other signals. Therefore, the actual distance may or may not reach 1000m.
If you stretches the telescopic antenna, it can have a further working range, which is twice as much as it used to be.
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 135mm x 42mm x 25mm
Weight: 95g
Uses: garage doors, motorcycles, car alarm products, home security products, wireless remote control products, industrial control products.
 
Usage:
The receiver paired to this transmitter can be turned on / off by pressing buttons on the transmitter, connecting the red wire and black wire of the transmitter or connecting the red wire and black wire to a switch/sensor.
 
Controlling the receiver by pressing buttons on the transmitter:
Press big button on the transmitter -> On, the device controlled by the receiver starts to work;
Press small button on the transmitter -> Off, the device controlled by the receiver stops working.
 
Controlling the receiver by connecting red wire and black wire of the transmitter:
When connecting the red wire and black wire of this transmitter, the transmitter will be triggered and then it will send an RF signal of "ON" to turn on the receiver, the device controlled by the receiver will starts to work.
When disconnecting the red wire and black wire of this transmitter, the transmitter will be triggered and then it will send an RF signal of "OFF" to turn off the receiver, the device controlled by the receiver will stops working.
 
The transmitter can also be triggered by connecting the red wire and black wire to a switch or a sensor, but the switch or sensor must be normally open (NO).
 
Add Receiver:
This transmitter can remote control different receivers, including :
S1L-DC12 (DC, Relay Output, 1 Channel, Latched Control Mode)
S1XL-DC12 (DC, Power Output, 1 Channel, Latched Control Mode)
S1U-DC12 (DC, Relay Output, 1 Channel, Momentary, Latched and Toggle Control Mode)
S1X-DC12 (DC, Power Output, 1 Channel, Momentary, Latched and Toggle Control Mode)
S1PX DC12 (DC, Power Output, 30A High Power,1 Channel, Momentary, Latched and Toggle Control Mode)
S1PU-DC12 (DC, Relay Output, 30A High Power, 1 Channel, Momentary, Latched and Toggle Control Mode)
S1L-AC220 (AC, Relay Output, 1 Channel, Latched Control Mode)
S1U-AC220 (AC, Relay Output, 1 Channel, Momentary, Latched and Toggle Control Mode)
S1X-AC220 (AC, Power Output, 1 Channel, Momentary, Latched and Toggle Control Mode)
S1PX-AC220 (AC, Power Output, 30A High Power,1 Channel, Momentary, Latched and Toggle Control
 
How to set up the 8-bits code of the transmitter:
1. Open the transmitter shell, then you will see the circuit board. There are two rows pads and one row of chip feet on the back side.
2. The upper row of pads is “L” side, and the lower row of pads is “H” side.
3. If solder the middle row of chip feet to the “L” side, it is code 1. If solder the middle row of chip feet to the “H” side, it is code 2. Don’t solder to any side, it is code 0.
4. The 8-bits code order is from left to right (from A1 to A8).
5. Here is an example, the 8-bits code in the picture is 00010121, solder as the following way:
6. Code 0: don’t solder any side, like A1A2A3A5.
7. Code 1: solder to the “L” side, like A4A6A8.
8. Code 2: solder to the “H” side, like A7.
Download the User Manual: Wireless Receiver ,Remote Controller
Ask A Question
* Required information

*
*
fqeh
*