Hi, I'm Tom. Welcome to our shop,
Carymart offers you the premium rf remote control equipment.
We suggest you reading our FAQs before making your decision.
If you have any other question, please contact us.
We will reply you as soon as possible.
Application:
Mainly used for doors, windows, cellars, trapdoors, hatchways, solar
tracking system, medical devices, agricultural machinery, vehicles, ships,
elevator platforms, lifting tables, TV lifts, robots, cabinetries, massage
sofas, electric beds, medical chairs, and other electrical equipment. It can
open, close, push, pull, lift, and descend these devices.
It can replace hydraulic and pneumatic products to save power consumption.
Feature:
High-quality products and high-quality services
New housing design, high working stability
Metal housing, able to work in very harsh environments.
Metal gearbox, high strength wear-resistant gear
Aluminum alloy telescopic tube and outer tube, good corrosion resistant
Heavy duty design, high-power DC motor
Strong thrust, up to 2000N / 200 Kgs / 450 lbs.
Multiple speed options, from 5 mm/second to 160 mm/second
Multiple stroke options, from 10 mm to 1500 mm
We can customize any stroke length from 10mm to 1500mm, such as 380mm,
750mm, 1250mm and so on.
Advanced waterproof and dustproof technology
Low power consumption and low noise
Built-in two limit switches, linear actuator will automatically stop when
stroke rod reaches the limit position.
Built-in limit switch signal output is optional.
Built-in potentiometer is optional.
Built-in Hall sensor is optional, so you can use the synchronous controller
to operate 2, 3 or 4 linear actuators fully synchronously.
With auto-locking capability to hold load position after stopping, and no
power supply is required.
Maintenance-free
Specifications:
Optional working voltage: DC 12V, DC 24V, DC 36V or DC 48V, and 24V is the
most commonly used working voltage.
Stroke range: 16 inches or 400 mm
Optional speed: 5±1mm/s, 10±2mm/s, 15±3mm/s, 20±4mm/s, 25±5mm/s, 40±8mm/s,
55±10mm/s, 65±12mm/s, 100±15mm/s, 160±20mm/s
The above is the speed at no load, and the actual working speed will
gradually slow down as the load increases.
Max load capacity: 2000N / 200 Kgs / 450 lbs at 5mm/s
Linear actuator can get maximum load capacity when it operates in the
vertical direction, and the pulling force is less than pushing force.
No-load current: 0.5~1A at 12V or 0.3~0.5A at 24V
Full load current: 3~6A at 12V or 1.5~3A at 24V
Please use a 12V/6A or 24V/3A power supply to power a linear actuator or use
a 12V/10A or 24V/5A power supply to power two linear actuators, or use a
12V/20A or 24V/10A power supply to power three or four linear actuators.
Shaft diameter: 20mm
The diameter of the mounting holes for the front and rear connectors: 6mm
[0.236 in]
Housing material: Aluminum Alloy
Stroke rod material: Aluminum Alloy
Gear material: Steel Alloy
Motor type: Brushed DC Motor
The front connector style can be customized: the default is an open hole
connector, which can be customized with slotted connector, internal thread
connector, etc. And you can provide drawings for customization.
The orientation of the front connector is default, we can rotate it 90
degrees during the production according to the customer's needs.
Duty cycle: 20%, max 5mins continuous use
Service life: approx. 25,000 cycles
Power cable: two-core wire for normal linear actuators; five-core wire for
linear actuators with built-in potentiometers; six-core wire for linear
actuators with built-in Hall sensors; four-core, five-core or six-core wire
for linear actuators with built-in limit switch signal outputs.
Cable length of the normal linear actuator: 500±10%mm [20 in], the length
can also be customized according to your specific needs.
Certifications: CE
Environment temperature: -26℃ to 85℃
Operating noise: about 46dB~56dB (Linear actuators with different parameters
will have different noise levels.)
IP rating: IP65
Stroke and Length (Model 0041506):
Stroke: 400MM.
Rretraction Length: When the linear actuator is fully retracted, the center
distance between the two mounting holes is 550MM.
Extension Length: When the linear actuator is fully extended, the center
distance between the two mounting holes is 950MM.
The linear actuator has two built-in limit switches, When the linear
actuator is fully retracted or fully extended, it will stop automatically.
We can adjust the position of the built-in limit switches during production
to meet customer-specified stroke and retraction lengths. For example,
specify the stroke length of 380MM and the retraction length of 570MM.
Note: The specified retraction length must be greater than the original
length, and the specified stroke must be less than the original stroke.
Operation:
When the brown power wire is connected to the positive pole of the DC power
supply and the blue power wire is connected to the negative pole of the DC
power supply, the stroke rod will extend outward; after switching the power
in the reverse direction, the stroke rod will retract inward.
Note:
1. If you need a power supply to power linear actuator, please click
here
to purchase.
2. If you want to use external limit switches to stop linear actuator at any
position, please click
here
to purchase.
3. If you want to use a remote control switch to operate linear actuator
wirelessly, please click
here
to purchase.
4. If you want to control 2, 3 or 4 linear actuators fully synchronously,
you need to purchase built-in Hall effect sensors for each linear actuator, and buy a
synchronization controller, please click
here
to purchase.
Different no-load speeds and corresponding maximum thrust:
No-load Speed
Full load Speed
Maximum Thrust
Self-locking Force
5mm/s
2.5mm/s
2000N / 200 kg / 450 lbs
2200N / 220 kg / 490 lbs
10mm/s
5mm/s
1000N / 100 kg / 200 lbs
1100N / 110 kg / 250 lbs
15mm/s
7.5mm/s
800N / 80 kg / 180 lbs
900N / 90 kg / 200 lbs
20mm/s
10mm/s
700N / 70 kg / 160 lbs
800N / 80 kg / 180 lbs
25mm/s
13mm/s
600N / 60 kg / 130 lbs
700N / 70 kg / 160 lbs
40mm/s
20mm/s
350N / 35 kg / 80 lbs
400N / 40 kg / 90 lbs
55mm/s
28mm/s
250N / 25 kg / 60 lbs
300N / 30 kg / 70 lbs
65mm/s
33mm/s
200N / 20 kg / 50 lbs
250N / 25 kg / 60 lbs
100mm/s
50mm/s
150N / 15 kg / 30 lbs
100N / 10 kg / 20 lbs
160mm/s
80mm/s
100N / 10 kg / 20 lbs
50N / 5 kg / 10 lbs
Note:
1. The above data is the maximum load capacity that can be obtained when the
linear actuator runs in the vertical direction. If the weight of your
equipment (such as a cellar door) is 100kg, and you want to use a linear
actuator to open this door, you need to calculate the actual force acting on
the linear actuator according to your installation method. This force is
usually 2-5 times the weight of the cellar door. If you don't know how to
calculate it, please contact us for help.
2. The above is the speed at no load, and the actual working speed will
gradually slow down as the load increases. Full load speed is approximately
60-70% of No-load speed.
3. Different speeds correspond to different maximum loads. Please select the
right speed according to the speed and maximum load you need.
4. Linear actuators are not recommended for continuous operation under
maximum load, we recommend letting it work at about half of the maximum load
to get a longer working life.
5. For linear actuators with a stroke greater than 500MM, you should not
normally allow them to operate at their maximum stroke under heavy loads. If
the actual stroke you want is 600MM, we recommend that you choose a linear
actuator with a stroke of 700-800MM.
6. When the speed of the linear actuator is 100mm/s or 160mm/s, the
self-locking force is much smaller than the thrust. At other speeds the
self-locking force is greater than the thrust.
7. The maximum pull force of the linear actuator is slightly less than its
maximum thrust force.
Production time:
The linear actuators are the customized products, and these products are not in
stock, we need to spend 3~7 working days to produce them according to the
specified parameters in your order.
Return or Exchange:
The Linear Actuators are the customized products, we need to produce them
according to the specified parameters in your order, so that we do not
accept returns or cancel orders. If customers order unsuitable linear
actuators themselves, we also do not accept exchanges, please understand.
We can provide 3D CAD model files in STEP format for linear actuators.
Please contact us by e-mail if you need them.
